How To Build A Quarter Pipe

How To Build A Quarter Pipe

If you’re wondering how to build a quarter pipe - this is the article for you. We took a deep dive, and this should answer all of your relevant DIY questions - even if you’ve never seen a jigsaw, studs, or a circular saw in your life.

[Everything to know about grip tape.]

How Do You Make A Quarter Pipe Skateboard Ramp?

Here’s what you’ll need:

1. Skateboard

2. 4x4s or 2x4s

3. Plywood

4. Nails or screws

5. Tape measure

6. Hammer or screwdriver

7. Level

8. Saw (optional)

Assuming you have all of the necessary materials, follow these simple steps to build your own quarter pipe skateboard ramp:

1. Choose a level spot in your yard or driveway to construct the ramp. You will need two 4x4s or two 2x4s for the base of the ramp, and one sheet of plywood for the ramp itself.

2. Cut the lumber to size using a saw, if necessary.

3. Assemble the base of the ramp by nailing or screwing the 4x4s or 2x4s together.

4. Cut the plywood to size and attach it to the ramp base with nails or screws.

5. Use a level to make sure the ramp is level before skating on it.

Here are some more detailed instructions:

Once you have your plywood cut out, you need to make sure that the edges are smooth. You can use a router or a sanding block to do this. After the edges are smooth, you need to attach the two pieces of plywood together. You can do this with screws or nails. Make sure that you predrill the holes so that the wood doesn't split.

After the two pieces of plywood are attached, you need to cut out the transition template. This is the piece that will go in between the two pieces of plywood and create the quarter pipe shape. Once you have the transition template cut out, you need to attach it to one of the pieces of plywood. Again, you can use screws or nails to do this.

Now you need to cut the plywood along the lines of the transition template. You can use a saw or a router to do this. Once you have the plywood cut, you need to sand down all of the edges so that they are smooth.

Now you need to attach the two pieces of plywood together with the transition piece in between. You can use screws or nails to do this. Make sure that you predrill the holes so that the wood doesn't split.

Now you should have a quarter pipe shaped piece of plywood. You can now attach it to your skateboard deck using screws or nails. Make sure that you predrill the holes so that the wood doesn't split.

And that's it! You now have a quarter pipe skateboard ramp that you can use to practice your tricks.

[Want skateboarder socks?]

  • 💰
    Best Board

    Stoked Ride Shop Complete
  • Stoked Ride Shop Skateboard Complete in Black
  • Why it's rad: Hand built in CA. Dragon BUILT Bearings are a premium bearing and the tool + wax are a rad bonus to round out this great deal.
  • Buy at Stoked Buy at Amazon

How Much Does It Cost To Build A Quarter Pipe?

The cost of building a quarter pipe depends on a few factors, such as the materials you use and the size of the ramp. However, you can expect to spend around $200-$300 on a basic quarter pipe. If you want a more elaborate setup, the cost will increase accordingly. Quarter pipes are a great addition to any skatepark or backyard ramps, and they can provide hours of fun for skaters of all levels. With a little bit of planning and some elbow grease, you can have your very own quarter pipe in no time.

What Materials Do You Need To Make A Quarter Pipe?

To make a quarter pipe, you will need some plywood, 2x4s, decking screws, and concrete. You will also need a power drill and a saw. The first step is to cut the plywood into four equal pieces. Then, you screw the 2x4s onto the plywood to create a frame. Next, you screw the decking screws into the 2x4s to secure them in place. Finally, you pour concrete into the frame and let it set. Once it has set, you can remove the quarter pipe from the frame and use it for skateboarding.

What Wood Is Used For Quarter Pipes?

Plywood is often used for quarter pipes due to its availability, affordability, and easy-to-use nature. It is also a sturdy material that can withstand the weight of a skateboarder and the impact of repeated tricks. Quarter pipes made out of wood are typically found in skate parks and private residences.

[Here is how to build a quarter pipe.]

What Is The Height Of A Quarter Pipe?

There is no definitive answer to this question as the height of a quarter pipe can vary depending on its purpose and location. For example, a quarter pipe used for skateboarding might be different in height than one used for BMX biking. Additionally, a quarter pipe located indoors might be different in height than one located outdoors. Ultimately, the height of a quarter pipe will be dictated by its intended use.

What's The Difference Between A Half Pipe And Quarter Pipe?

The main difference between a half pipe and quarter pipe is the size of the transition. A half pipe has a larger transition, which means it is taller and can be ridden faster. A quarter pipe has a smaller transition, which means it is shorter and can only be ridden at slower speeds.

Both types of pipes are often used in skate parks, but they can also be found in street skating spots. Half pipes are more common in skate parks because they offer a more challenging ride for experienced skaters. Quarter pipes are more common in street skating spots because they are easier to do tricks on.

How Do You Make A Quarter Pipe Out Of Pallets?

First, you will need to gather your materials. For this project, you will need:

-4 pallets

-Nails

-Hammer

-Plywood

-Saw

Now that you have your materials, it's time to get started. Begin by nailing two of the pallets together side-by-side. Then, take the other two pallets and do the same thing. Now you should have two long rectangles made out of pallets.

Next, take your plywood and cut it into four equal pieces. These will be used to reinforce the joints between the pallets. Nail the plywood onto the inside corners of the pallets, making sure that the nails are evenly spaced.

Now it's time to start shaping your quarter pipe. Begin by sawing off the top two boards of both rectangles. You should now have two ramps with a sloped edge.

To finish, nail the two ramps together at the sloped edges. Your quarter pipe is now complete.

[The amazing Nyjah Huston.]

How Do You Make A 2 Foot Quarter Pipe?

If you're looking to up your skateboarding game, then learning how to make a 2 foot quarter pipe is a great place to start. This type of ramp is perfect for practicing tricks and can be built relatively easily at home. Here's what you'll need:

 

-4 sheets of plywood

-8 2x4s

-Construction adhesive

-Nails or screws

-1/2 inch decking screws

-1/2 inch diameter bolts with nuts and washers

-Paint or sealant (optional)

First, cut the plywood into four equal pieces using a saw. Then, cut the 2x4s into eight equal pieces. Next, attach two of the 2x4s to each piece of plywood using construction adhesive and nails or screws. Be sure to use screws that are long enough to go through the plywood and into the 2x4s.

After the 2x4s are attached, it's time to add the decking. Start by screwing the 1/2 inch decking screws into the plywood around the perimeter, making sure to countersink them so they're flush with the surface. Then, continue screwing them in every 6 inches or so across the surface of the ramp.

Now it's time to assemble everything. Place two of the pieces of plywood together, sandwiching two of the 2x4s between them. Then, bolt them together using the 1/2 inch diameter bolts, washers, and nuts. Repeat this process with the remaining two pieces of plywood and 2x4s.

Once everything is bolted together, your 2 foot quarter pipe is complete. You can optionally paint or seal it to protect it from the elements. And that's it - enjoy skating on your new ramp.

[Here is the incredible Shaun White.]

How Do You Make A Mini Halfpipe?

To make a mini halfpipe, you will need:

-4 sheets of plywood

-1 sheet of OSB or similar type of wood

-2x4s (8 feet long)

-Deck screws

-Construction adhesive

-Carpenter's level

-Circular saw

-Jigsaw

-Hammer

-Nail Gun

-Plywood cutting jig (optional)

Building a mini halfpipe is a great way to get started in skateboarding. It can be done relatively cheaply and easily, and it will provide hours of fun. Here's how to do it:

1. Cut the plywood sheets into strips that are 8 feet long and 4 feet wide. You will need four strips total.

2. Cut the OSB or similar sheet into strips that are 8 feet long and 2 feet wide. You will need two strips total.

3. Assemble the frame of the halfpipe by screwing the plywood strips together with deck screws, using construction adhesive to help hold them in place. Make sure that the frame is level as you work.

4. Cut out the transition (the curved part) of the halfpipe using a circular saw and a jigsaw. A plywood cutting jig can be used to make this process easier, but it is not necessary.

5. Attach the OSB or similar strips to the top and bottom of the halfpipe frame using deck screws. These will serve as the riding surface.

6. Cut 2x4s into 8-foot lengths and use them to brace the sides of the halfpipe. Nail them into place with a hammer or nail gun.

Your mini halfpipe is now complete! Enjoy skating on it for hours of fun. Remember to practice safety while skateboarding, and always wear a helmet.

[Need off road electric skateboards?]

How To Build A Mini Ramp For Skateboarding

Building a mini ramp for skateboarding is a great way to progress your skills and have some fun. There are a few things you need to consider before you start building, such as the size of the ramp, the materials you use and the location.

When you have considered these factors, it's time to start building! Here's how to build a mini ramp for skateboarding:

1. Decide on the size of the ramp. The most common sizes are 4ft wide by 8ft long, or 6ft wide by 12ft long. If you're unsure, go for the smaller size to begin with.

2. Choose your materials. The most common material used for ramps is plywood, but you can also use MDF or OSB.

3. Cut the pieces of plywood to size using a saw. If you're not confident using a saw, ask someone else to help you.

4. Nail or screw the pieces of plywood together to form the ramp shape. Make sure the nails or screws are driven in at an angle so they don't come out the other side.

5. Cover the nails or screws with something smooth, like duct tape, electricians tape or gaffer tape. This will stop you from catching your wheels on them and getting hurt.

6. Place the ramp in your chosen location and start skating! Remember to practice safety first and always wear pads and a helmet when skating.

Building a mini ramp for skateboarding is a great way to have some fun and progress your skills. With a little planning and some basic DIY skills, you can easily build your own ramp. Just remember to practice safety first.

[There are the best skateboard waxes.]

Other Factors To Consider

If you don’t want to do some light woodworking, you can buy Keen Ramps, or a ramp from DIYSkate. Amazon has even more choices, including a grind box, wide quarter pipes, kicker ramps, pipe ramps, and more.

However, if you go the DIY route to build a skateboard quarter pipe, you may want to head to Home Depot with a long materials list - as there are even more ways you can customize your ramps. You may want a longer transition radius, steel coping, masonite, PVC piping, a steel plate, chalk lines - there’s so much you can do, if you check out some of the beginners tutorials on YouTube. Happy skating! 🛹 🤙

Stoked Ride Shop may earn a commission if you purchase a product through one of our links.

Leave a comment

All comments are moderated before being published.

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Free shipping

Free shipping on orders over $25 within the lower 48